<

Corotech® Specialty and Flooring Primers

100% Solids Epoxy Pre-Primer

100% Solids Epoxy Pre-Primer

Semi-Gloss (V155)

100% Solids Epoxy Pre-Primer is formulated for use on both steel and masonry. For rusted steel where extensive surface preparation is needed, but not logistically possible, the penetrating properties and extended dry time — 16 hours at 77 °F — of this two-component epoxy seal crevices and other imperfections, promoting better adhesion for subsequent coats. For prepared masonry surfaces, V155 penetrates and seals, providing an excellent foundation for subsequent coats of Corotech epoxy floor coatings. The unique, 100% solids formula of V155 forms a sealed epoxy barrier that inhibits future corrosion.

  • Low viscosity easily fills voids and crevices
  • Does not shrink - eliminates craters
  • Chemical and fume resistant
  • Extended cure time allows maximum penetration
  • Seals previously coated concrete, masonry, and galvanized metal
  • Qualifies for LEED certification

Colorant Used: N/A
Color System Supported: N/A

  • Available Colors: Clear
  • Sheen (or Gloss): Semi-Gloss
  • Cleanup: Solvent
  • Resin Type: 2-Component Epoxy
  • Recommended Use: Interior, Exterior
  • MPI Rating:
  • VOC Level: 6.0
TECHNICAL DATA SHEETS
SEE DETAILS HIDE DETAILS
Clear Acrylic Sealer

Clear Acrylic Sealer

Low Lustre (V027)

Clear Acrylic Sealer is a waterborne, fast drying, clear acrylic coating formulated as an easy-to-apply seal coat on bare concrete floors and other masonry surfaces. This product is designed to allow for easy sweep up of dust and to reduce water penetration or erosion, efflorescence, spalling, and chalking without changing the natural appearance of the substrate. Areas exposed to heavy-duty industrial traffic or severe exterior conditions may require multiple coats.

  • Rapid dry
  • Soap and water clean-up
  • Can be used over a variety of substrates
  • Blister and alkali fume resistant
  • Low odor

Colorant Used: N/A
Color System Supported: N/A

  • Available Colors: Clear
  • Sheen (or Gloss): Low Lustre
  • Cleanup: Soap and Water
  • Resin Type: Acrylic
  • Recommended Use: Interior, Exterior
  • MPI Rating:
  • VOC Level: 164.0
SAFETY DATA SHEETS
TECHNICAL DATA SHEETS
SAFETY DATA SHEETS
SEE DETAILS HIDE DETAILS
Moisture Tolerant Quick Set Epoxy Sealer

Moisture Tolerant Quick Set Epoxy Sealer

Semi-Gloss (V156)

Moisture Tolerant Quick-Set Epoxy Sealer is a two-component, fast-dry, waterborne polyamide hybrid sealer for masonry floors. It is an excellent primer/basecoat for high-performance epoxy floor systems, with fast-dry performance. This product can also be used as a stand-alone clear finish on masonry floors (2 coats).

  • Fast set – recoat in 5 hours
  • Can tolerate slightly damp masonry
  • Suitable for use in USDA inspected facilities
  • Water clean-up with low odor
  • May be used as a stand-alone semi-gloss clear coat (2 coats)

Colorant Used: N/A
Color System Supported: N/A

  • Available Colors: Clear
  • Sheen (or Gloss): Semi-Gloss
  • Cleanup: Soap and Water
  • Resin Type: 2-Component Waterborne Polyamide Epoxy
  • Recommended Use: Interior
  • MPI Rating:
  • VOC Level: 94.0
TECHNICAL DATA SHEETS
SEE DETAILS HIDE DETAILS
Organic Zinc Rich Primer

Organic Zinc Rich Primer

Flat (V170)

Organic Zinc Rich Primer is a heavy-duty corrosion inhibitor for interior or exterior ferrous metal and weathered galvanized metal. It is made from an organic thermoplastic resin and leaves a finished film that is 83% zinc. Ideal for touching up existing galvanized metal with no topcoat.

  • High zinc content delivers cathodic protection
  • Can be top coated or left uncoated
  • Thermoplastic resin requires tie coat under certain finishes; check TDS
  • Cold Galvanizing Project Qualification
  • Meets Composition Requirements of TT-P-1046
  • Meets Performance Requirements of TT-P-641 & DOD-P-21035
  • Meets Performance Requirements of Mil-P-26915 Type I, Class A
  • Meets SSPC Paint #5 & SSPC Paint #20, Type II

Colorant Used: N/A
Color System Supported: N/A

  • Available Colors: Gray
  • Sheen (or Gloss): Flat
  • Cleanup: Soap and Water
  • Resin Type: Thermoplastic Rubber
  • Recommended Use: Interior, Exterior
  • MPI Rating: 18
  • VOC Level: 500.0
SAFETY DATA SHEETS
TECHNICAL DATA SHEETS
SAFETY DATA SHEETS
SEE DETAILS HIDE DETAILS
Polyamide Epoxy Primer

Polyamide Epoxy Primer

Flat (V150)

Polyamide Epoxy Primer is formulated for use on ferrous and non-ferrous metals in industrial and commercial applications. This two-component, rust-inhibitive epoxy primer is an excellent choice for use as a rust-inhibitive base coat when used as part of a high-performance coating system. With proper top coating, it demonstrates excellent resistance to moisture and chemicals, including solvents, acids, and alkalis. Polyamide Epoxy Primer is also suitable for use on concrete substrates in secondary containment and immersion service applications.

  • High-solids content
  • Outstanding protection against corrosion
  • Engineered for use in general metal finishing and fabrication
  • Also appropriate for chemical processing facilities and transportation infrastructure finishing
  • Suitable as a high-performance tie coat; especially over existing epoxies
  • Suitable for use in USDA-inspected facilities

Colorant Used: N/A
Color System Supported: N/A

  • Available Colors: Red and Gray
  • Sheen (or Gloss): Flat
  • Cleanup: Solvent
  • Resin Type: Polyamide Epoxy
  • Recommended Use: Interior, Exterior
  • MPI Rating:
  • VOC Level: 322.0
TECHNICAL DATA SHEETS
SEE DETAILS HIDE DETAILS

MORE TOOLS

Dinner plates in variety of bright colors against yellow wall

FIND YOUR COLOR

Our color finder gives you several inspirational starting points.

GO
Dark blue paint rolled onto wall

Paint Calculator

Tell us the dimensions of the room, and we'll tell you how much paint to buy.

GO